Biopharmaceutical

Specifications: 1"-6",DN10-DN150
Material：ASTM304/316L,1.4301/1.4404
Inner surface：Ra0.8μm，mechanical polishing and Electro polishing
outer surface：Ra0.8μm，mechanical polishing
Standards：DIN11851、RJT、SMS、DS、ISO、IDF,etc
Authentication：3-A-63-03；EN 10204-3.1 Certificate

Clamp Hose fitting are used to connect the part by hose in pipeline or some equipment
Specifications：1/2"-6",DN10-DN150
Connection mode：Clamps, welding, thread
Standard：DIN Inch
Material：ASTM 304/316L,1.4301/1.4404

Pipe Holder
Type: Hexagon，Round,Rubber anti-vibration
Specifications: 1/2"-8",DN10-DN200
Material：ASTM304/316L,1.4301/1.4404
Connection mode：welding, thread
Applicable Standards：DIN11852/11850、AS1528、SMS、DS、BS4825、ISO、IDF,etc.
Authentication, 3-A-63-03；EN 10204-3.1 Certificate；

Specifications: 1/2"-8",DN10-DN200
Material：ASTM304/316L,1.4301/1.4404
Specifications: 1/2"-8",DN10-DN200
Material：ASTM304/316L,1.4301/1.4404
Inner Surface：Ra0.5μm，Mechanical Polishing & Electro Polishing
Outer Surface：Ra0.8μm，Mechanical Polishing
Connection : Ferrule, Welding, Thread
Standards：DIN11852/11850、AS1528、SMS、DS、BS4825、ISO、IDF,etc.
Authentication: 3-A-63-03；EN 10204-3.1 Certificate；

The DIN 11864 series Flange and Union are design by sterilization and no dead corner. Same with ASME BPE . It is especially suitable for the pipeline system in biological pharmaceutical sterilization high cleanliness requirement.
Aseptic Flange size:1/2"-6",DN10-DN150
Aseptic Union size:1"-6",DN25-DN150
Aseptic Ferrule size：1/2"-6"，DN10-DN150
Gasket：EPDM；FPM，FDA177.2600，3-A-18-03
Surface Finish: DIN 11866
Mechanical Polishing：0.4μm=HE4c
Electro Polishing：0.25μm=HE5c
Material：1.4404；1.4435 NB2 Fe＜0.5%

Similar Products：Y-Tee, U-tee, R-tee
Wall Thickness:1.2mm,1.5mm,1.65mm,2.0mm,2.8mm
Material: ASTM304/316L,1.4301/1.4404
Implementation of Standards ：DIN11850 SMS ISO IDF DS BS4825 AS1528
High-grade Standard：ASME BPE 316L DIN11866 1.4404
Inner Surface：Mechanical PolishingRa0.4μm,0.8μm；Electro Polishing：Ra0.4μm
Outer Surface：Ra0.8μm

Thermal Insulation Jacket Pipe
The design has an insulating jacket shell, in order to achieve the best heat transfer.It can protect the easy solidification sensitive medium, cases of chocolate, margarine or similar media holding liquid flow
Specifications：DN25-DN100，1"-4"
Material: ASTM304/316L,1.4301/1.4404
Connection mode：Clamp,threaded,flanged
Standards:DIN11850 SMS ISO IDF DS BS4825 AS1528
Inner Surface: Mechanical Polishing Ra0.4μm,0.8μm；
Outer Surface：Ra0.8μm

High purity stainless steel piping
Specifications:1/2"10",DN10-DN250,
Wall Thickness:1.2mm,1.5mm,1.65mm,2.0mm,2.8mm
Material: ASTM304/316L,1.4301/1.4404，ASME BPE 316L
Implementation of Standards ：DIN11850 SMS ISO IDF DS BS4825 AS1528
High-grade standard：ASME BPE 316L DIN11866 1.4404
Inner Surface: Mechanical Polishing Ra0.4μm,0.8μm；Electro polishing：Ra0.4μm
Outer Surface：Ra0.8μm

Product type:elbow,tee,reducer,threaded connector
Specifications: 1/2"-8",DN10-DN200
Material：ASTM304/316L,1.4301/1.4404
Inner surface：Ra0.5μm，mechanical polishing & Electro polishing
outer surface：Ra0.8μm，mechanical polishing
Standards：DIN11852/11850、AS1528、SMS、DS、BS4825、ISO、IDF,etc
Authentication：3-A-63-03；EN 10204-3.1 Certificate；

Product Type：elbow,tee,reducer,clamp connector,cross
Specifications: 1/2"-8",DN10-DN200
Material：ASTM304/316L,1.4301/1.4404
Inner surface：Ra0.5μm，mechanical polishing & Electro polishin
outer surface：Ra0.8μm，mechanical polishing
Connection mode：Clamps, welding, thread

Weld Pipe Fittings Series
Product Type:Elbow, Tee, Reducer,Ferrule,Cross
Size: 1/2"-8",DN10-DN200
Material：ASTM304/316L,1.4301/1.4404
Inner surface：Ra0.5μm，mechanical polishing & Electro polishing
Outer surface ：Ra0.8μm，mechanical polishing
Connection : Clamps, welding, thread
Implementation of standards：DIN11852/11850、AS1528、SMS、DS、BS4825、ISO、IDF,etc.
Authentication:3-A-63-03；EN 10204-3.1 Certificate

I-Line fitting is the ideal choice for industrial of food,brewing, oil and water solution. I-Line fittings can stand higher vibrations,temperatures and pressure than other available connections. It is easy to disassembly and complies with food grade.
Specifications1"-8"
Material:ASTM 304/316L
Surface Treatment：180grit/300Grit
Gaskets Select :EPDM/FPM/NBR/Silicong
Certified by 3A-63-02, in line with the FDA.177.2600

It is the best choice for biological control of high cleanliness requirements of the pipe fittings.
At first Pipes and fittings of high quality can shorten the installation of preparation. Second, it can avoid practical welding arc deflection phenomenon in operation and is easy operated by automatic welding machine and no need adjust parameters repeatedly . It saves the welding time ,eventually shortens the construction period.

Pipeline：1“-6”
Elbow：1“-6”
Tee：1"-6"
Reducer：1"-6"
Ferrule：1/2"-6"
Instrument Tee：1、2“-1.5
Mechanical Polishing：Ra0.51μm=SF1
Electro Polishing：Ra0.38μm=SF4
Material：ASTM 316L

●The floor drain is applicable to the food,modified material, pharmaceutica in sanitary and clean workshop.
●Stainless steel: AISI304/316L
●Size: 1"-4",DN25-DN100
●Mesh and plug head prevent particle material go into drain pipe
●Remove cover and sludge hopper to clean floor drain in case of the propagation of bacteria

The duplex filters applies to purify solids that cannot be seen with the naked eye, such as milk, sugar, soft drinks and other liquid in the barrel. Two filters are used interchangeably, Don't need stop it to replace or wash the filter. It is suitable for continuous production.
Filter body material：AISI 316L、AISI 304
Gasket：EPDM FDA 177.2600
Inner surface treatment：Ra＜0.4μm
Hole Dia：0.5mm to 2.0mm
Mesh size：30Grits to 300Grits
Size：DN 25-DN150/1"-6"
Working temperature：-10℃-120℃(EPDM)
Max. working pressure：10bar 145PSI

Filter are widely used in the auxiliary service for food processing, cosmetic, chemicals and pharmacy industries. With high hygienic design,it is mainly used to filter the particulates which will damage pumps and some other equipment .The filter is basiclly consist of inlet outlet and filter body. Filter mesh is installed inside to remain all particles equal or greater than mesh

Size：DN25-DN150 1"-6"
Working temperature：-10℃-120℃(EPDM)
Max. working pressure：10bar 145PSI
Gasket：Silicon MVQ FPM
Connection: clamp,thread, weld
Standard:DIN,SMS,RJT,IDF,3A
Hole Dia：0.5mm to 2.0mm
Mesh size: 30 Grits to 300 Grits

Filter are widely used in the auxiliary service for food processing, cosmetic, chemicals and pharmacy industries. With high hygienic design,it is mainly used to filter the particulates which will damage pumps and some other equipment. The filter is basiclly consist of inlet outlet and filter body. Filter mesh is installed inside to remain all particles equal or greater than mesh
Size：DN25-DN150 1"-6"
Working temperature：-10℃-120℃(EPDM)
Max. working pressure：10bar 145PSI
Gasket：Silicon MVQ FPM
Connection: clamp,thread, weld
Standard:DIN,SMS,RJT,IDF,3A
Hole Dia：0.5mm to 2.0mm
Mesh size: 30 Grits to 300 Grits

Filter are widely used in the auxiliary service for food processing, cosmetic, chemicals and pharmacy industries. With high hygienic design,it is mainly used to filter the particulates which will damage pumps and some other equipment.The filter is basiclly consist of inlet outlet and filter body. Filter mesh is installed inside to remain all particles equal or greater than mesh

Size：DN25-DN150 1"-6"
Working temperature：-10℃-120℃(EPDM)
Max. working pressure：10bar 145PSI
Gasket：Silicon MVQ FPM
Connection: clamp,thread, weld
Standard:DIN,SMS,RJT,IDF,3A
Hole Dia：0.5mm to 2.0mm
Mesh size: 30 Grits to 300 Grits

●The principle is same as micro-filter's. It can prevent the outside particulates coming into the storage tank due to the liquid level descends. It ensures the air purity in the tank.
●Housing material: 316L or 304
●Inner surface polished
●Surface roughness:Ra≤0.2μm
●Capacity: 0.75m3/min、1.5m3/min、3m3/min
●Connection size：1"-2.5"，DN25-DN65
●Connection mode: Clamp, Flange

Filter with condensation water mainly applies in the container system
Connection size：1"-2.5",DN25-DN65
Filter area: single-core 5/10 "20""30",etc.
Material：304/316L
Surface treatment：Ra≤0.5μm
Drain valve: diaphragm valves, basic

Micro pore filter can eliminate the particulates and bacteria larger than 0.1um from liquids and gas due to the following advantages: high precision, fast speed, low adsorption, no media falling off, acid-resistant, lye-resistant, easy operation, etc. It is widely used in pharmacy, chemical, electronics,beverage, winery, biochemical treatment, environment protection and so on.
Capacity:0.5t/h~25t/h
Pressure：0.1-0.6mpa
Filter cartridge1 core, 3 cores, 5cores, 7 core
Size：10"、20"、30"、40"
Materials：PTFE/PE/NYLON/PP
Hole dia：0.1μm、0.22μm、1μm、3μm、5μm、10μm
Connections:flat style(226)/ plug in (222)
Internal surface polish: Ra<0.2um
Cartridge material：ASTM304/316L

The manhole is square shape with open lid,mainly used in food, wine, beverage, pharmaceutical and other industries tank equipment.
◎Outward opening man hole cover
◎Spanner type handle, hand wheel handle
◎Internal surface：Ra0.8μm-0.5μm
◎Outside surface: polishing finished, matt finished, sand-blasting finished.
◎Max. pressure：1.0bar
◎Gasket：EPDM 、NBR、SILICON、FPM conform to FDA177.2600
◎Size：235*185,425*335，535*435
◎Height： 65，80，100，120，150
◎Material：AISI304(1.4301)/316L(1.4404)

The Square manhole is square shape with open lid,mainly used in food, wine, beverage, pharmaceutical and other industries tank equipment.
◎Outward opening man hole cover
◎Hand wheel handle
◎Internal surface：Ra0.8μm-0.5μm
◎Max. pressure：1.0bar
◎Size：235*185
◎Height： 65，80，100，120，150
◎Material：AISI304(1.4301)/316L(1.4404)

The manhole oval design mainly used in food, wine, beverage, pharmaceutical and other industries on the tank equipment.
◎ Size: 435 * 335,530 * 430,635 * 525
◎ Height: 75,100,120,150
◎ Inward opening manhole cover
◎ Spanner type handle, hand wheel handle
◎ Internal surface: Ra0.8μm-0.5μm
◎ Outer surfaces: Mirror polish,Matt finish, sand-blasting
◎ Max. pressure: 3.0bar
◎ Gasket: EPDM, NBR, SILICON, FPM conform toFDA177.2600
◎ Material: AISI304 (1.4301) / 316L (1.4404)
◎ Certification: 3-A-84-02; FDA177.2600