Food

◆The aseptic sampling valve is designed for sterilization before and after each sampling.
◆Open to Sampling-Valve is opened by rotating the handle
◆Closed to Sterilizing-The built-in spring closes the valve. Do Keep hose channel open while sterilizing and recommend to install a small safety valve on the outside if sterilizing by steam.
◆Appplication: The aseptic sampling valve is applied to beer, milk, beverage, fruit juice, pharmacy industries etc.
◆Connection: clamp, welding
◆Valve body material：AISI 316L（1.4404）ASME BPE 316L
◆Membrane：EPDM PTFE
◆Max. Temperature：130℃(EPDM)
◆Max. Temperature：150℃(PTFE)
◆Pressure：10bar
◆Certificate：3-A-55-02，PED/97/23/EC

◎Specifications:DN8-DN50,1/2"-2"
◎Material：CF8/304，CF8M/316
◎Nominal pressure：PN1.6，2.5，4.0，6.4MPa
◎Strength test pressure：PN2.4，3.8，6.0，9.6MPa
◎High pressure seal pressure test：1.8，2.8，4.4，7.1MPa
◎Applicable medium：H1 H-(16-64)C Water, oil, gas
◎Applicable temperature：-40~180℃

◎Check valve is designed to prevent fluid from flowing back and ensure the flow to one way direction.
◎It can be used to reduce the loss of fluid back suction,avoid pipe is shock by liquid
◎It is used in the food-processing, beverages, winery, oil, cosmetics,pharmaceuticals and chemicals industries.
◎The valve is open when pressure of the fluid exceeds the spring pressure and it is closed when the two pressures are close equal.And stronger counter-pressure also makes the valve closed.
◎Specifications: DN-25/1" TO DN-100/4"
◎Boby/shaft: AISI 316L/304
◎Spring: AISI 304
◎Seal: EPDM according to FDA177.2600
◎Surface Treatment: Ra ≤0.8 μm
◎Seal: NBR, FPM (Viton) or PTFE. FDA 177.2600(optional)
◎Connections: weld, thread, clamp, DIN, SMS, RJT, IDF, ISO,3A
◎Max. pressure：10 bar
◎Opening pressure：0.3bar(DN-25) 0.2bar(DN-32/40) 0.1bar(DN-50/100)
◎Working temperature ： -10℃ to 130℃(EPDM)

Pneumatic angle seat valve with control unit is a general switch in the automatic control system widely used in printing, dyeing, bleaching, food,washing,chemical, water treatment, pharmacy and other automatic machinery and equipment. It is featured with water hammer protection,noise-free, reliable sealing performance.

Size：1/2"-3",DN10-DN80
Material：CF8、CF8M
Connection : Clamp, weld, thread，BSP/BSTP/NPT,DIN,Inch
Control unit
Position feedback, Can be viewed on (Green) off (Red)
Built-in Solenoid valve
Valve opens– green light
Valve closes-red light
The design has inching button (manual design)
Power Supply：DC 24V ±10%
Air supply：M5/Φ4

Pneumatic angle seat valves with Positioner is mainly used in the flow control valve adjustment. The medium contacting with the valve and the position is only stainless steel and PTFE. Maximum temperature can reach to 180 ℃, pressure up to 20bar. It can also be used in vacuum environment. According to the design of valve body without dead angle, surface roughness up to Ra0.4 μ m,valve seal with embedded designs, it is used very broadly covering almost all sectors, such as pharmaceuticals, food andbeverage, brewery, chemical and other industries. The valve is particularly suitable for steam flow regulating control system.

◆Size: 1/2"-3", DN10-DN80
◆Material: CF8/304、CF8M/316
◆Connection : Clamp,thread,flange,BSP,BSP,NPT,DIN
◆Working pressure：8bar(standard) 10bar(Options)
◆Working temperature：120℃(standard) 180℃(Options)
●0/4...20mA to 0...5/10V（standard）
●0/4...20mA Position feedback output (Options)
●Device NET Device Net bus control (Options)
●Support single self-tuning function
●Protection grade IP67
●Power Supply DC 24V ±10%
●Support manual and automatic operation

Pneumatic angle seat valve is a general switch in the automatic control system which is widely used in printing, dyeing, bleaching, food,washing,chemical, water treatment, pharmacy and other automatic machinery and equipment. It is featured with water hammer protection,noise-free, reliable sealing performance.
Design Features
● Size: 1/2"-2 1/2", DN10-DN65
● Material: CF8/304、CF8M/316
● Connection : Clamp,thread,flange,BSP、BSP、NPT,、DIN
● Pneumatically operated:
1）Can be configured to position sensor
2）valve locator (process controller)
3）Valve position Regulator
4）MINI C-TOP Control unit
●Manual pneumatic interchangeable
●Working pressure：8bar(standard) 10bar(option)
●Working temperature：120℃(standard) 180℃(option)

Application
Angle seat valve is a general switch in the automatic control system which is widely used in printing, dyeing, bleaching, food,washing,chemical, water treatment, pharmacy and other automatic machinery and equipment. It is featured with water hammer protection,noise-free, reliable sealing performance.

Design Features
● Size: 1/2"-2 1/2", DN10-DN65
● Material: CF8/304、CF8M/316
● Connection : Clamp,thread,flange,BSP、BSP、NPT,、DIN
● Pneumatically operated:
1）Can be configured to position sensor
2）valve locator (process controller)
3）Valve position Regulator
4）MINI C-TOP Control unit
●Manual pneumatic interchangeable
●Working pressure：8bar(standard) 10bar(option)
●Working temperature：120℃(standard) 180℃(option)

◎ Specifications: DN8-DN50,1 / 2 & quot; -2 & quot;
◎ Nominal pressure: PN1 .6,2.5,4.0,6.4MPa
◎ strength test pressure: PT2.4,3.8,6.0,9.6MPa
◎ High pressure seal pressure test: 1.8,2.8,4.4,7.1MPa
◎ Applicable medium: J11W- (16-64) C water, oil, gas, J11W- (16-64) P nitric acid, J11W- (16-64) R acetic acid
◎ Applicable temperature: -40 ~ 180 ℃
◎ Material: CF8, CF8M

◎Specifications：DN15-DN200,1/2"-8"
◎Nominal pressure：PN1.6-6.4, Class 150/300,10k/20k
◎Strength test pressure：PT1.5PN
◎High pressure seal pressure test：1.1PN
◎Applicable medium：J41H-(16-64)C water, oil, gas J41W-(16-64)P nitric acid J41W-(16-64)R acetic acid
◎Applicable temperature：-40~180℃
◎Material：CF8、CF8M

Horizontal pneumatic three way non retention ball valve, the hygienic design of the valve is widely used in the field of food processing, beverages, fruit juices, wine, biopharmaceutical with vary flexible body combinations, for example, L-Port or T-Port which can be interchangeable on-site Inlet and outlet to be any combination of changes for guaranting zero dead angle and no retention.

Technical specifications
Size：1"-4",DN25-DN100
Material：1.4301/304,316L/1.4404
Gaskets：PTFE,TFM(FDA 177.1550)
Max. temperature：-20℃ - 150℃(Standard)-30℃ - 200℃(Option)
Pressure:10-30bar(Depending on seal material and temperature)
Operating modes:manual, pneumatic, electric
Surface finishing:Internal surface Ra0.6μm, external surface sand blast
Certificate：3-A-68-00，PED/97/23/EC
Configuration Controls：process controller/valve positioning ，0/4....20mA,0 5/10V(see controller directory)(Option)
Top of the valve control unit，AS-1 Device Net bus communication terminal connection(Option)
position sensor PNP NPN(Option)

Three way non-retention ball valve, the hygienic design of the valve is widely used in the field of food processing, beverages, fruit juices, wine, biopharmaceutical with vary flexible body combinations, for example, L-Port or T-Port which can be interchangeable on-site Inlet and outlet to be any combination of changes for guaranting zero dead angle and no retention.

Technical specifications
Size：1"-4",DN25-DN100
Material：1.4301/304,316L/1.4404
Gasket：PTFE,TFM(FDA 177.1550)
Max. temperature：-20℃ - 150℃(Standard)-30℃ - 200℃(Option)
Pressure:10-30bar(Depending on seal material and temperature)
Operating modes:manual, pneumatic, electric
Surface finishing:Internal surface Ra0.6μm, external surface sand blast
Certificate：3-A-68-00，PED/97/23/EC
Configuration Controls：process controller/valve positioning ，0/4....20mA,0 5/10V(see controller directory)(Option)
Top of the valve control unit，AS-1 Device Net bus communication terminal connection(Option)
position sensor PNP NPN(Option)

Pneumatic three way non-retention ball valve, the hygienic design of the valve is widely used in the field of food processing, beverages, fruit juices, wine, biopharmaceutical with vary flexible body combinations, for example, L-Port or T-Port which can be interchangeable on-site Inlet and outlet to be any combination of changes for guaranting zero dead angle and no retention.

Technical specifications
Size：1"-4",DN25-DN100
Material：1.4301/304,316L/1.4404
Gaskets：PTFE,TFM(FDA 177.1550)
Max. temperature：-20℃ - 150℃(Standard)-30℃ - 200℃(Option)
Pressure:10-30bar(Depending on seal material and temperature)
Operating modes:manual, pneumatic, electric
Surface finishing:Internal surface Ra0.6μm, external surface sand blast
Certificate：3-A-68-00，PED/97/23/EC

Horizontal pneumatic three way ball valve is mainly used in the processing and beverage, wine, oil refining, cosmetics and chemical industries.

Design Features
●Size：1"-4",DN25-DN100
●Temperature：-20℃ to 120℃
●Pressure：10-bar
●Material：AISI 304 316L
●Gaskets:PTFE FDA 177.1550
●Whatever the connection is, it does not change the total length of the valve
●Connection : Clamp, weld, thread,flange,DIN、SMS、RJT、FIL
●Material contact parts AISI，304/316L
●Other parts AISI 304
●Certificate：PED，97/23EC

Pneumatic three way ball valve, both manually and automatically operated valve are mainly used in processing beverages, wine, oil refining, cosmetics and chemical industries.

Design Features
●Size：1"-4",DN25-DN100
●Temperature：-20℃ - 120℃
●Pressure：10-bar
●Material：AISI 304 316L
●Gaskets:PTFE FDA 177.1550
●No matter what kind of liquid flow is, the handle can be mounted on the side of the valve body
●Whatever the connection is, it does not change the total length of the valve
●Connection : Clamp, weld, thread,flange,DIN、SMS、RJT、FIL
●Material contact partsAISI，304/316L
●Other parts AISI 304
●Certificate：PED，97/23EC

Three way ball valve, both manually or automatically operated 3 way ball valve are mainly used in processing beverages, wine, oil refining, cosmetics and chemical industries.

Design Features
●Size：1/2"-4",DN10-DN100
●Temperature：-20℃ - 120℃
●Pressure：10-bar
●Material：AISI 304 316L
●Smaller and lighter than the other valve
●Operating torque is small
●Gaskets:PTFE FDA 177.1550
●Whatever the connection, do not change the total length of the valve
●Connection : Clamp, weld, thread,Flange,DIN、SMS、RJT、FIL
●Can be equipped with pneumatic actuators, electric actuators
●Material contact parts:AISI，304/316L
●Certificate：PED/97/23/EC

Specifications：1/2"-4",DN10-DN100
Material：CF8/304，CF8M/316
Strength test pressure：1000WOG,2000WOG
sealing pressure：1.6Mpa
Applicable temperature：-40℃-180℃
Connection mode：BSP/BSTP/NPT,Butt / Socket Weld

Pneumatic three-piece ball valve
Specification 1/2"-4", DN10-DN100
Material: CF8, CF8M
Pressure: 1.0Mpa
Temperature: -40 ° C to 180 ° C

Integral leak-proof ball valve
Nominal pressure：PN1.6，2.5，4.0，6.4MPa
Strength test pressure：PT2.4，3.8，6.0，9.6MPa
Low pressure seal pressure test：0.6MPa
Applicable temperature：-40~180℃
Material：CF8、CF8M

Thin Type Flange Ball Valve
◎Specifications：DN15-DN100
◎Nominal Pressure：PT1.6, 2.5, 4.0, 6.4MPa
◎Strength test Pressure：PT2.4, 3.8, 6.0, 9.6MPa
◎Low Pressure Seal Pressure Test：0.6MPa
◎Applicable Medium：Q41F-(16-64)C water, oil, gas
Q41F-(16-64)P nitric acid
Q41F-(16-64)R acetic acid
◎Applicable Temperature：-40～180℃
◎Material：CF8、CF8M

Specifications：1/2"-4",DN10-DN100
Material：CF8/304，CF8M/316
Strength Pressure：1000WOG,2000WOG
sealing pressure：1.6Mpa
Applicable temperature：-40℃-180℃
Connection mode：BSP/BSTP/NPT,Butt / Socket Weld

Specifications：1/2"-4",DN10-DN100
Material：CF8/304，CF8M/316
Strength Pressure：1000WOG,2000WOG
sealing pressure：1.6Mpa
Applicable temperature：-40℃-180℃
Connection mode：BSP/BSTP/NPT,Butt / Socket Weld

Specifications：1/2"-4",DN10-DN100
Material：CF8/304，CF8M/316
Strength Pressure：1000WOG,2000WOG
sealing pressure：1.6Mpa
Applicable temperature：-40℃-180℃
Connection mode：BSP/BSTP/NPT,Butt / Socket Weld

The tank bottom ball valve is used for pressure vessels and storage tanks of draining and discharging with the fully inclusive designed ball seat and compensation automatic type sealing . So it has advantage of high pressure, high temperature resistance, small torque, long life and other characteristics to meet CIP and SIP cleaning and sterilization. It is very suitable for the application in high cleanliness requirements in process systems such as pharmaceutical, food and beverage, dairy products, chemical industry etc..
◆ Tank bottom ball valve can configure a variety of different actuators, electric, pneumatic and manual are interchangeable.

Design Features
●Size：1"-4",DN25-DN100
●Material ：304/1.4301，316L/1.4404
●Max. temperature：-30℃ - 130℃
●Max.Pressure：Vacuum -10bar
●Operating torque is small
●Excretable
●No matter what the flow fluid is, the handle can be mounted on the side of the valve body
●No matter what kind of connection is, the valve can be replaced without change the length of valve.

◆The tank bottom ball valve is used for pressure vessels and storage tanks of draining and discharging with the fully inclusive designed ball seat and compensation automatic type sealing . So it has advantage of high pressure, high temperature resistance, small torque, long life and other characteristic to meet CIP and SIP cleaning and sterilization. It is very suitable for the application in high cleanliness requirements in process systems such as
pharmaceutical, food and beverage, dairy products, chemical industry etc..
◆Pneumatic tank bottom ball valve can configure a variety of different actuators, electric, pneumatic and manual are interchangeable.

Design Features
●Size：1"-4",DN25-DN100
●Material ：304/1.4301，316L/1.4404
●Max. temperature：-30℃ - 130℃
●Max.Pressure：Vacuum -10bar
●Operating torque is small
●Excretable
●No matter what the flow fluid is, the handle can be mounted on the side of the valve body
●No matter what kind of connection is, the valve can be replaced, without change the length of valve