Multi-port single seat valve has a multi-functional combination application, can add product on the process pipeline, main valve CIP cleaning and SIP sterlization, the lowest point liquid self-emptying and other functional applications.
Multi-port single seat valve has a multi-functional combination application, can add product on the process pipeline, main valve CIP cleaning and SIP sterlization, the lowest point liquid self-emptying and other functional applications.
PTFE diaphragm isolate the valve from outside circumstance completely
Size: DN10-DN150, 1/2"-6"
Material: 304/1.4301, 316L/1.4404, ASME BPE 316L 1.4435 NB2 Fe≤0.5%
Standard: DIN SMS ISO IDF RJT BS4825 ASME BPE 3A DIN11864 DIN11853
Connection: thread, clamp, flange, weld
Drive mode: Film-type pneumatic actuator
Pressure: vacuum to 10bar (1.0Mpa)
Temperature: max 140℃
Seal material: EPDM SILICON FKM FFKM HNBR FVMQ NBR
Certificattion: FDA177.2600; Glass II USP Glass VI Chapter 88; GB4806.11; EG VO/1935-2004; PED/97/23/EC
Film-type single seat valve can bear higher pressure ≤ 30, shorter height, stainless steel
Technical Specifications
Size: DN10-DN150, 1/2"-6"
Material: 304/1.4301, 316L/1.4404, ASME BP
The vent valve is a reliable automatic venting valve that removes air as needed and is mounted vertically on top of the pipe or vessel.
The following is an example of the use of an exhaust valve:
Shown 1: Due to material or process requirements, the canisters form cavitation and therefore require air to be
vented. In this case, the valve is mounted on the top of the container.
●Specifications: 1"-12", DN25-DN200
●Material: ASTM 304/1.4301, 316L1.4404
● Washer: EPDM FPM
● Pressure: 10bar
● Temperature: -10 ° C to 130 ° C
DJ-FDT butterfly valve is mainly designed for powder, granule, capsule and other container equipment systems. The butterfly valve has the characteristics that standard butterfly valve does not have, such as ultra-small torque, seal opening and closing does not produce excessive friction, long life, No seal powder shedding, ultra-short valve body, and adjustable pressure. The valve does not require professional tools to be disassembled, maintained,
cleaned, safe, reliable, low cost, simple to operate, and can be interchanged manually, pneumatically, or electrically.
Specifications: 4''-10'', DN100-DN250
Connection method: clamp, welding, flange, bottom flange, DIN 3A INCH
Material: 316L/1.4404/1.4435
Seal: White SILCON (recommended) Gray FKM (selection)
Execution mode: manual, pneumatic, electric interchangeable
Surface treatment: Ra 0.6μm (recommended); Ra 0.4μm (selection)
External surface: matt (recommended) bright blasting electropolishing
Applicable: vacuum, high temperature 130 ° C, CIP cleaning, SIP sterilization, etc.
The DJ-D71BV is a clip-on centerline butterfly valve. The valve body consists of a ring-shaped seat, an elastic lining and a disc. The disc is rotated 90° through the valve shaft into the washer to control the fluid. Depending on the model and size, working pressures up to 25 bar and media temperatures up to 210 °C are possible. In most cases, these valves are used to control pure liquids, but can also be used for other media such as gases through special selection. Due to the wide variety of materials, butterfly valves are widely used in industries such as chemical and water treatment. Butterfly valves are also a very economical fluid solution in some process segments where the frequency of opening and closing, hygienic level and control accuracy are not critical. Butterfly valves are usually the only alternative for pipeline applications larger than DN 150. In the case of higher requirements for corrosion resistance or sanitary grade, a lined butterfly valve can be used. PFA-encapsulated discs for highly aggressive media in the chemical or semiconductor industry; polished stainless steel discs for use in the food or pharmaceutical industry.
Specifications SIZE: 1.5"-12", DN40-DN300
Material: valve body CF8 (304); valve plate CF3M (316L), CF8 (304), stainless steel + PFA
Pressure: PN10; PN16
Temperature: EPDM -20 ° C to +130 ° C, other materials refer to the following data table
Seal: EPDM SILICON FKM HNBR NBR PTFE TFM
Connection method: clip type, lug type
Drive mode: manual, pneumatic, electric
DJ-FDT butterfly valve is mainly designed for powder, granule, capsule and other container equipment systems. The butterfly valve has the characteristics that standard butterfly valve does not have, such as ultra-small torque, seal opening and closing does not produce excessive friction, long life, No seal powder shedding, ultra-short valve body, and adjustable pressure. The valve does not require professional tools to be disassembled, maintained, cleaned, safe, reliable, low cost, simple to operate, and can be interchanged manually, pneumatically, or electrically.
Specifications: 4''-10'', DN100-DN250
Connection method: clamp, welding, flange, bottom flange, DIN 3A INCH
Material: 316L/1.4404/1.4435
Seal: White SILCON (recommended) Gray FKM (selection)
Execution mode: manual, pneumatic, electric interchangeable
Surface treatment: Ra 0.6μm (recommended); Ra 0.4μm (selection)
External surface: matt (recommended) bright blasting electropolishing
Applicable: vacuum, high temperature 130 ° C, CIP cleaning, SIP sterilization, etc.
DJ-FDT butterfly valve is mainly designed for powder, granule, capsule and other container equipment systems. The butterfly valve has the characteristics that standard butterfly valve does not have, such as ultra-small torque, seal opening and closing does not produce excessive friction, long life, No seal powder shedding, ultra-short valve body, and adjustable pressure. The valve does not require professional tools to be disassembled, maintained,
cleaned, safe, reliable, low cost, simple to operate, and can be interchanged manually, pneumatically, or electrically.
Specifications: 4''-10'', DN100-DN250
Connection method: clamp, welding, flange, bottom flange, DIN 3A INCH
Material: 316L/1.4404/1.4435
Seal: White SILCON (recommended) Gray FKM (selection)
Execution mode: manual, pneumatic, electric interchangeable
Surface treatment: Ra 0.6μm (recommended); Ra 0.4μm (selection)
External surface: matt (recommended) bright blasting electropolishing
Applicable: vacuum, high temperature 130 ° C, CIP cleaning, SIP sterilization, etc.
Proportional pneumatic cut-off regulating valve is used in dairy, food, beverage production, bio-pharmaceutical, fine chemical, water treatment, new energy and other industries. The valve controls various fluid flows, temperatures, pressures, and so on.
Proportional pneumatic adjustment butterfly valve is used in dairy, food, beverage production, bio-pharmaceutical, fine chemical, water treatment, new energy and other industries. The valve controls various fluid flows, temperatures, pressures and so on.
Input signal: 0/4-20mA
Bus communication: MODE BUS RS485
Input signal: 0/4-20mA, 0-5/10V (optional)
Output signal: 0/4-20mA, 0-5/10V (optional)
Display: OLED Chinese menu
Material: 304/1.4301, 316L/1.4404, 1.4435, 2205
Specification: 1/2"-12", DN10-DN300
Temperature: -20 ° C to 150 ° C
Pressure: vacuum -10bar
Air source pressure: 4-7bar
Power supply: DC 24V ±10%
Health certification: 3-A-53-06; PED-97/23/EC; FDA177.2600
Explosion-proof certification: II 2 G Ex ib IIC T6/T5/T4
Proportional pneumatic adjustment ball valve is used in dairy, food, beverage production, bio-pharmaceutical, fine chemical, water treatment, new energy and other industries. The valve controls various fluid flows, temperatures, pressures and so on
Input signal: 0/4-20mA
Bus communication: MODE BUS RS485
Input signal: 0/4-20mA, 0-5/10V (optional)
Output signal: 0/4-20mA, 0-5/10V (optional)
Display: OLED Chinese menu
Material: 304/1.4301, 316L/1.4404, 1.4435, 2205
Specification: 1/2"-6", DN10-DN150
Temperature: -20 ° C to 150 ° C
Pressure: vacuum -10bar
Air source pressure: 4-7bar
Power supply: DC 24V ±10%
Health certification: 3-A-53-06; PED-97/23/EC; FDA177.2600
Explosion-proof certification: II 2 G Ex ib IIC T6/T5/T4
Diaphragm type Pneumatic control valve is used in dairy, food, beverage production, bio-pharmaceutical, fine chemical, water treatment, new energy and other industries. The valve controls various fluid flows, temperatures, pressures and so on
Manual pneumatic integrated, membrane pneumatic proportional control valve, which can be applied to various flow control and adjustment systems, and can be applied in various industrial fields such as chemical, sewage treatment, dairy, food, beverage production, pharmaceutical and fine. Industrial fields such as chemical industry. The most important applications are pressure control, flow control, liquid level, temperature control, etc.
Control input: 0/4-20mA/0-5V/10V
Feedback output : 0/4-20mA/0-5V/10V
Power supply : DC24V ± 10%
Bus communication: MODE BUS RS485
Accuracy: Repeat positioning accuracy ≤ 0.2%;
Menu: OLED display Chinese & English
Setting: One-button auto-tuning function
Operating mode: manual / automatic
Fault: gas cut, power off, automatic valve position reset (standard) valve position hold function (optional)
Stroke angle: 0-180°
◆The valve position is not consuming when it is kept
◆Power supply: DC24V ±10%
●Scope of application: straight stroke and angular travel 30°-180°
●Aluminum alloy casing
●Explosion-proof grade ExdIIBT4 (optional)
●IP68 protection level
ITS-100 is a rotary angular stroke pneumatic valve position feedback device designed primarily for valve process position feedback. It is compatible with most PLC (Programmable Logic Controller) automation systems and used to control all types of process valves. . It can be mounted on a variety of pneumatic valves, such as pneumatic butterfly valves, ball valves, globe valves and other rotary stroke valves.....
Passive signal
Feedback output: 2 passive signals
Open: Green
Close: red
Stroke angle: 0-180°
Active signal
Feedback Output : PNP DC 24V
Open: Green
Close: red
Stroke angle: 0-180°
DJ-CIP-L series self-priming pump not only optimizes the internal structure, impeller design, dead angle treatment, machine seal pressure balance design and the machine seal is completely in the flushing area， but?also optimized the external hygiene of the pump to make it more hygienic and reduce the dead angle inside. Because there is no dead zone, it is very easy to be cleaned by CIP, SIP sterilization and so on. In addition, we have maintained the most flexible combination of DJ-CIP series pumps. For example, the pump outlet angle can be adjusted from 0° to 135°, It?keeps the pump maintenance and maintenance and machine seal replacement efficient. The requirement for a high degree of professionalism is reduced, and these do not require special tools. Therefore, the goal of achieving high efficiency, hygiene, high reliability and low cost is to make the DJ-CIP series pump into?high performance self-priming pump.
Maximum flow rate Max Flow rate: 40m3/h
Maximum head Max Head: 42 H/M
Maximum suction Max suction: 8 / M
Temperature: -20 ° C to 130 ° C Temperature: -20 ° C to 130 ° C
Power power :1.5-15KW
Material Material: 304 /316L, 1.431/1.4404, ASME BPE 316L, 1.4435 NB2 Fe≤0.5%
Surface treatment: ≤ Ra0.8μm, ≤ Ra0.6μm, ≤ Ra0.4μm
Machine seal: single machine seal, double machine seal
Inlet/Outlet Connection: Thread, Clamp, Flange, Aseptic Flange
Certification: 3-A-02-10 (N.O.1579); MD/06/42-EC (N.O.70521616101-00); FDA 177.2600; USP CLASS-II; EG/VO1935/2004;
The STU series is a full-stainless steel positive displacement cam rotor pump designed according to the strict sanitary requirements of 3A-02-11 of the United States. It is very suitable for food processing, beverages, juices, dairy products, cosmetics, pharmaceutical industries, etc. The transport of low-viscosity materials can be carried out with solid particulate materials and applied to CIP, SIP systems. The pump has features not found in other volumetric pumps, such as low pulse, high pressure, rotary two-way reversible and flexible functional combinations.
Maximum flow Max.flow: 90m3 / h / 395 GPM
Maximum pressure Max.pressure: 15bar/220 Psi
Maximum temperature Max.Temperature: 150°C/302°F
Maximum speed Max.rev: 750 rpm
Material: 316L, 1.4404, ASME BPE 316L, 1.4435 NB2 Fe ≤ 0.5%
Surface treatment: ≤ Ra0.8μm, ≤ Ra0.6μm, ≤ Ra0.4μm
Certification : 3-A-02-11 No.1759; FDA 177.2600; CE-MD/06-42 No .705201402401-00
Twin-screw pump has self-priming ability and can transport various complex conditions such as solid particles, gas-liquid mixture, high viscosity, low viscosity and material transportation and extraction; it not only used for material extraction and Conveying, also applicable to CIP and SIP systems, can reduce pipeline, valve control, CIP dedicated pumps, Not only improve?efficiency, but also reduces costs. The pump also has the performance that other volumetric pumps do not have, such as no pulse phenomenon, no damage to particles, high pressure, speed range and large flow range.
Max flow: 110m3/h
Max Particles: 23mm
Max pressure: 20 bar
Speed range: 10-3500 R.P.M
Working temperature (Max Temperature): -40 ° C to 150 ° C
Surface treatment: Ra≤0.6μm; EP=Ra0.4μm
Material: 100% stainless steel, medium contact part 316L.
Certification: 3-A-02-11 No.1759; FDA 177.2600; CE-MD/06-42 No .705201402401-00
Twin-screw pump has self-priming ability and can transport various complex conditions such as solid particles, gas-liquid mixture, high viscosity, low viscosity and material transportation and extraction; it not only used for material extraction and Conveying, also applicable to CIP and SIP systems, can reduce pipeline, valve control, CIP dedicated pumps, Not only improve efficiency, but also reduces costs. The pump also has the performance that other volumetric pumps do not have, such as no pulse phenomenon, no damage to particles, high pressure, speed range and large flow range.
Max flow: 110m3/h
Max Particles: 23mm
Max pressure: 20 bar
Speed range: 10-3500 R.P.M
Working temperature (Max Temperature): -40 ° C to 150 ° C
Surface treatment: Ra≤0.6μm; EP=Ra0.4μm
Material: 100% stainless steel, medium contact part 316L.
Certification: 3-A-02-11 No.1759; FDA 177.2600; CE-MD/06-42 No .705201402401-00
Twin-screw pump has self-priming ability and can transport various complex conditions such as solid particles, gas-liquid mixture, high viscosity, low viscosity and material transportation and extraction; it not only used for material extraction and Conveying, also applicable to CIP and SIP systems, can reduce pipeline, valve control, CIP dedicated pumps, Not only improve efficiency, but also reduces costs. The pump also has the performance that other volumetric pumps do not have, such as no pulse phenomenon, no damage to particles, high pressure, speed range and large flow range.
Max flow: 110m3/h
Max Particles: 23mm
Max pressure: 20 bar
Speed range: 10-3500 R.P.M
Working temperature (Max Temperature): -40 ° C to 150 ° C
Surface treatment: Ra≤0.6μm; EP=Ra0.4μm
Material: 100% stainless steel, medium contact part 316L.
Certification: 3-A-02-11 No.1759; FDA 177.2600; CE-MD/06-42 No .705201402401-00
RX series flexible pump is a positive displacement pump with excellent self-priming performance, and its self-priming capacity can reach 5 meters. The efficiency of pumping viscous products almost reaches the effect of pumping water.
The sampling valve has a dead angle-free design and the end face connected to the container does not have a dead zone phenomenon.
◎ It is mainly used for sample collection of materials in tank equipment or pipelines. It can also be installed at the lowest point of tank equipment or pipelines to drain residual liquid.
◎Working principle: the handwheel rotates the valve stem clockwise together with the sealing ring. At this time, the valve is opened for sampling. The handwheel rotates the valve stem counterclockwise together with the sealing ring. The valve is closed.
◎Applicable temperature: -10 ° C to 130 ° C
◎ valve body material: AISI 304 AISI 316L
◎ Sealing material: PTFE
◎Connection method: clamp type, thread type, welding type, nut type
equipment systems. The butterfly valve has the characteristics that standard butterfly valve does not have, such as ultra-small torque, seal opening and closing does not produce excessive friction, long life, No seal powder shedding, ultra-short valve body, and adjustable pressure. The valve does not require professional tools to be disassembled, maintained, cleaned, safe, reliable, low cost, simple to operate, and can be interchanged manually, pneumatically, or electrically.
Specifications: 4''-10'', DN100-DN250
Connection method: clamp, welding, flange, bottom flange, DIN 3A INCH
Material: 316L/1.4404/1.4435
Seal: White SILCON (recommended) Gray FKM (selection)
Execution mode: manual, pneumatic, electric interchangeable
Surface treatment: Ra 0.6μm (recommended); Ra 0.4μm (selection)
External surface: matt (recommended) bright blasting electropolishing
Applicable: vacuum, high temperature 130 ° C, CIP cleaning, SIP sterilization, etc.
Lobe pump is available in a variety of configurations, TU series is standard configuration . STU series is all stainless steel. It is a positive displacement cam rotor pump designed according to the strict sanitary requirements of the US 3A-02-11. It is very suitable for transportation of various highly viscous and low-viscous materials such as food processing, beverages, juices, dairy products, cosmetics, the pharmaceutical industry can be carried out with solid particulate materials, also can be applied to CIP and SIP systems. The pump has features not found in other volumetric pumps, such as low pulse, high pressure, rotary two-way reversible and flexible functional combinations.
Maximum flow Max.flow: 90m3 / h / 395 GPM
Maximum pressure Max.pressure: 15bar/220 Psi
Maximum temperature Max.Temperature: 150°C/302°F
Maximum speed Max.rev: 750 rpm
Material: 316L, 1.4404, ASME BPE 316L, 1.4435 NB2 Fe ≤ 0.5%
Surface treatment: ≤ Ra0.8μm, ≤ Ra0.6μm, ≤ Ra0.4μm
Certification : 3-A-02-11 No.1759; FDA 177.2600; CE-MD/06-42 No .705201402401-00
Get A Free Quote
