Semiconductor

applications.
◆Mixproof valve is a high degree of double-seal valve. Through the interface between two fluids, this system can be implemented in two body synchronization process, preventing the possibility of contaminating materials. leakage chamber and leak detector is self- cleaning by valve seat.
●Size:DN40-1.1/2"to DN100-4"
●The valve is equipped with a normally closed pneumatic actuator
●Forged ball valve body
●If there is a gush of fluid leaks from bottom of valve tube, you can determine whether the seal is damaged
●Easy to remove( just removing the clamps is enough)
●Welded connection (mm or inch)
●Balance Protection Design
●Max.Operating Pressure：10bar
●Min.Operating Pressure：Absolute vacuum
●Working temperature：-10℃ - 130℃(140℃ For short periods or disinfection)
●Certificate：3-A-85-03，PED/97/23/EC,FDA177.2600 ●Compressed air pressure：5bar-7bar
●Gas connection：R1/8"(BSP)

The mixproof butterfly valve as a process element for the separation of media, is suitable for a variety of applications:
●In CIP systems, for separating CIP cleaning fluid
●In flush-out processes
●In water management
●Part of pipeline separates material
●In CIP/gas management (breweries)
●Storage tanks for separating product/CIP
● As CIP reflux valve in the the manifold
● Especially for liquids and no suspension / gas medium particles.
Size: DN25-DN100, 1"- 4"
Material: 1.4404 / 1.4301, 304/ 316L
Maximum Temperature: -10 ℃ - 130 ℃
Maximum Pressure: 10bar
Operation: Pneumatic/ Manual interchangeable
Control Box: C-TOP Basic type, C-TOP + AS-I communication
Seal: EPDM (standard) FPM / SILICON / NBR, FDA177.2600

Double seat butterfly valves can be used in food-processing, pharmacy and chemical industries. The Butterfly Valve offers an easy and safe separatation of products and prevents accidental mixing in case of gasket damage. It is often used to isolate materials that require safe separation and CIP Liquid in a single point (not in manifolds), or at the end of a manifold (e.g. CIP return) or entry of a CIP solution into a tank (through a cleaning ball).

Tank bottom valve is used to vent the container material and the material will not be stuck in the valve chamber, and the design of the seat opens to the inside of the container. It avoids the overvoltage because the pipe leads to the possibility of accidental opening of the valve. The tank bottom valve has 45 ° and 90 ° two designs, pneumatic and manual interchangeable.
●Size：DN25/1" to DN100/4"
●Temperature ：130℃
●Pressure：10bar
●Air supply：4-7bar
●Material：ASTM 304/1.4301，316L/1.4404
●Gaskets：EPDM、FPM、HNBR，FDA177.2600
●Treatment：Ra<0.8μm
●Certificate：3-A-53-06，PED/97/23/EC,FDA177.2600

●The tank bottom seat valve is a pneumatically operated single seat valve, which is assembled at the bottom of tank,used in diary,food processing, beverage,pharmaceutical and fine chemical industries.
●Tank bottom valve is used to vent the container material and the material will not be stuck in the valve chamber, and the design of the seat opens to the inside of the container. It avoids the overvoltage because the pipe leads to the possibility of accidental opening of the valve. The tank bottom valve has 45 ° and 90 ° two designs, pneumatic and manual interchangeable.
●Size：DN25/1" to DN100/4"
●Temperature ：130℃
●Pressure：10bar
●Air supply：4-7bar
●Material：ASTM 304/1.4301，316L/1.4404
●Gaskets：EPDM、FPM、HNBR，FDA177.2600
●Treatment：Ra<0.8μm
●Certificate：3-A-53-06，PED/97/23/EC,FDA177.2600

The tank bottom seat valve is a pneumatically operated single seat valve which is assembled at the bottom of tank,used in diary,food processing, beverage,pharmaceutical and fine chemical industries.
●Tank bottom valve is used to vent the container material and the material will not be stuck in the valve chamber, the design of the seat open to the inside of the container. It avoids the over voltage because the pipe leads to the possibility of accidental opening of the valve. The tank bottom valve has 45 ° and 90 ° two designs, pneumatic and manual interchangeable.

●Size：DN25/1" to DN100/4"
●Temperature ：130℃
●Pressure：10bar
●Air supply：4-7bar
●Material：ASTM 304/1.4301，316L/1.4404
●Gaskets：EPDM、FPM、HNBR，FDA177.2600
●Treatment：Ra<0.8μm
●Certificate：3-A-53-06，PED/97/23/EC,FDA177.2600

Mini divert seat valve is particularly suitable for the filling machine equipment and can replace the traditional type of rotary valve.
Guarantee of lifetime for 1.5 million operattion
◆Size:1/2"-3/4",DN15-DN20
◆Material：304/316L
◆Seal-in-one design
◆Meet the high frequency opens and closes
◆No dead angle designed to meet the requirements of 3A-85-00
◆Seal: FDA177.2600
◆Connection : Clamp, weld, thread, DIN、SMS、ISO

The valve mainly solves problem that cleaning ball long-term bubbles in the medium of the dead leg so that easy to produce bacteria to pollute media. Cleaning drain valve begins cleaning when it opens. It prevents cleaning ball and from medium to avoid the dead angle.
Cleaning drain valve is designed for pipeline and tank cleaning equipment online cleaning line.
●Size：DN25/1" to DN100/4"
●Temperature：130℃
●Pressure：10bar
●Air supply：4-7bar
●Material：ASTM 304/1.4301，316L/1.4404
●Gaskets：EPDM、FPM、HNBR，FDA177.2600
●inner surface treatment：Ra<0.8μm
●Surface treatment: sand blasting, polishing
●Configuration options: position sensor, control unit
●Certificate：3-A-53-06，PED/97/23/EC,FDA177.2600

The globe valve designed with a valve jacket shell to achieves the best heat transfer. It can keep the easy solidification sensitive medium, flow, such as chocolate, margarine or similar media.

●Size：DN25/1" to DN100/4"
●Temperature：130℃
●Pressure：10bar
●Air supply：4-7bar
●Material：ASTM 304/1.4301，316L/1.4404
●Gaskets：EPDM、FPM、HNBR，FDA177.2600
●Inner surface treatment：Ra<0.8μm
●Outer surface treatment：Sandblasting, polishing
●Configuration options: position sensor, control unit
●Certificate：3-A-53-06，PED/97/23/EC,FDA177.2600

The valve has a standard valve function with PTFE diaphragm isolation valve internal and external leakage. Leakage detection provides diaphragm damage condition by leakage pipe.

● Size: DN25 / 1 & quot; to DN100 / 4 & quot;
● Temperature: 130 ℃
● Pressure: 10bar
● Air source: 4-7bar
● Material: ASTM 304 / 1.4301,316L / 1.4404
● Seal: EPDM, FPM, HNBR, FDA177.2600
● Inner surface treatment: Ra & lt; 0.8 & mu; m
● Surface treatment: sandblasting, polishing
● Configuration options: position sensor, a control unit
● Certificate: 3-A-53-06, PED / 97/23 / EC, FDA177.2600

Reversing globe valve with slow device, adjusting the regulator can reduce the actuator speed, prevent clash of the valve core and the valve body to prevent vibration, as well as prolong the service life of the sealing ring.

● Size: DN25 / 1 "to DN100 / 4"
● Temperature: 130 ℃
● Pressure: 10bar
● Air supply: 4-7bar
● Material: ASTM 304 / 1.4301,316L / 1.4404
● Seal: EPDM, FPM, HNBR, FDA177.2600
● Inner surface treatment: Ra <0.8μm
● Surface treatment: sandblasting, polishing
● Configuration options: position sensor, a control unit
● Certificate: 3-A-53-06, PED / 97/23 / EC, FDA177.2600

Pneumatic divert seat valve with steam sterilization, a single seat pneumatic valve in sanitary field which has been widely used in the food processing industry, beverage production of pharmaceutical and fine chemical industries

The valve has a standard function of reversing seat valve equipped with a stem that can be sterilized by cleaning
fluid or steam to ensure the stem is thoroughly cleaned.

● Size: DN25 / 1 "to DN100 / 4"
● Temperature: 130 ℃
● Pressure: 10bar
● Air supply: 4-7bar
● Material: ASTM 304 / 1.4301,316L / 1.4404
● Seal: EPDM, FPM, HNBR, FDA177.2600
● Inner surface treatment: Ra <0.8μm
● Surface treatment: sandblasting, polishing
● Certificate 3-A-53-06, PED / 97/23 / EC, FDA177.2600

● pneumatic divert seat valve with control unit is a hygienic single seat pneumatically operated valve which has been widely used in the food processing industry, beverage production of pharmaceutical and fine chemical industries.
● The seat valve automatically operated by a single or double acting pneumatic actuators with compressed air to push the shaft to locate the valve open or closed position.
● single-acting cylinder actuators rotate 180 degrees to achieve a valve normally open and normally closed.

● Size: DN25 / 1 "to DN100 / 4"
● Temperature: 130 ℃
● Pressure: 10bar
● air supply: 4-7bar
● Material: ASTM 304 / 1.4301,316L / 1.4404
● Seal: EPDM, FPM, HNBR, FDA177.2600
● Processing: Ra <0.8μm
● Certificate: 3-A-53-06, PED / 97/23 / EC, FDA177.2600
Control unit:
● Power: DC 24V ± 10%
● Single acting (standard), double acting (option)
● Self-tuning Valve position feedback function
● Supports analog signal (4-20mA) & electrical (DC24V) Output
● Support for AS-I BUS
● Supports manual and automatic operation

◎ Standard switching type (B-type) makes valves open and close operations by switching circuit, meanwhile outputs a group of active contacts signal to indicate that valve is fully open or fully closed.
◎ Smart regulating type (A-type) realizes intelligent regulation and control through receiving a standard output signal 4-20mA.DC, 0-10V.DC or 1-5V.DC from computer or industrial instrument as well as outputs 4-20mA.DC standard feedback signal.
◎ Operating time from 7s to 100S
Size:1"-8",DN25-DN200
Material: 304 / 316L
Pressure: 10bar
Temperature: -30 to 130 ℃
Connection: clamp, thread, weld, three-piece flange
Standards: DIN SMS ISO IDF RJT

Butterfly valve, both manual and automatic operation, can be used in industrial applications in fluid products, such as food processing, pharmaceutical and chemical industries.
Size: DN10-DN300, 1/2 -12 "
Temperature: 130℃
Pressure: 10bar
Material: ASTM T304/T316L, 1.4301/1.4404
Connection: flange, Weld, Clamp, Thread, etc.
Operation standard: DIN SMS RJT 3A ISO IDF
Pneumatic Operation: Single action, Double action
Certificate: PED/97/23/EC, health wading license

Regulating pneumatic butterfly valve can be applied in various fluid control systems, such as food and beverage, wine, pharmaceutical and other industries. The valve has feature of no dead ends, large flow, simple maintenance, small volume appearance.
◆ Support: DEVICE NET BUS
◆ Standard: Single-acting, double-acting (option)
◆ One-touch auto-tuning function
◆ Support for manual operation
◆ Power Supply: DC 24V ± 10%
◆ Analog Signals: 0/4-20mA, 0-5/ 10V
◆ Size: 1"-4", DN25-DN100
◆ Material: 304 /316L
◆ Pressure: 10bar
◆ Temperature: 130 ℃
◆ Inner Surface Roughness: Ra0.4μm (option)
◆ Connection: weld, clamp, thread, flange and other standards

Regulating type pneumatic butterfly valve can be applied in various fluid control systems, such as food and beverage, wine, pharmaceutical and other industries. The valve has feature of no dead ends, large flow, simple maintenance, small volume appearance.
◆ Support: DEVICE NET BUS
◆ Single-acting(standard), double-acting (option)
◆ One-touch auto-tuning function
◆ Support for manual operation
◆ Power supply: DC 24V ± 10%
◆ Analog signals: 0 / 4-20mA, 0-5 / 10V
◆ Size: 1 "-4", DN25-DN100

Butterfly valve whatever manual or automatic operation can be used in food processing, pharmaceutical and chemical products, industrial fluid applications.

Size: DN10-DN300, 1/2"-12"
Temperature: 130 ℃
Pressure: 10bar
Material: ASTM T304 / T316L, 1.4301 / 1.4404
Connection: Threaded, Flange Welding, Clamp, etc.
Operation Standard: DIN SMS RJT 3A ISO IDF
Manual operation: Muti-handles, Pull handles
Certificate: PED / 97/23 / EC, health wading license
Pneumatic Operation: Single acting, Double acting, Triple action

Butterfly valve whatever manual or automatic operation can be used in food processing, pharmaceutical and chemical products, industrial fluid applications.

Size: DN10 to DN300, 1/2"-12"
Maximum Temperature: 150 ℃
Maximum Pressure: 10bar
Material: ASTM T304 / T316L, 1.4301 / 1.4404
Connection: Thread, Flange Welding, Clamp
Operation Standard: DIN SMS RJT 3A ISO IDF
Manual operation: Muti-handles, Pull handles
Certificate: PED / 97/23 / EC, health wading license

Butterfly valve, whatever manual or automatic operation can be used in food processing, pharmaceutical and chemical products, industrial fluid applications.
Size: 1/2"- 12", DN10-DN300
Material: 304 / 316L, 1.4301 / 1.4404
Pressure: 10bar
Temperature: 130 ℃
Connection: weld, thread, clamp, three flange
Operation Standard: DIN SMS ISO IDF RJT DS

Radial diaphragm valves are mainly manually and pneumatically operated with inside body finished Ra≤0.5 um, in order to meet the requirements of biopharmaceutical industry.
●Size: 3/4"-2.5", DN20-DN65
●Working Temperature: -10℃ to 120℃ (EPDM/ Silcon)
●Max.Pressure: 6bar
●Operation: manual/pneumatic interchangeable
●Actuator Pressure: 5bar-6bar
●Connection: Weld, Clamp, Other special connection

Tank Bottom Radial Diaphragm Valve
●Mainly used in pharmaceutical, biotech, health care, cosmetic and food industries, etc.
●In the pharmaceutical industry, valves can be used as process control valve, dosing valve, sampling valve and aseptic drain valve, etc.
●In the food industry, valves are often used as guide device, such as sampling valve, dosing valve (For example adding CO2/Nitrogen to beer, add seasoning to drink). Radial diaphragm valve are mainly manually and pneumatically operated with inside body finished Ra≤0.5 um, in order to meet the requirements of biopharmaceutical industry.
● Size: 3/4 "-2.5", DN20-DN65
● Working Temperature: -10 ℃ to 120 ℃ (EPDM/ Silcon)
● Maximum Pressure: 6bar
● Operation: Manual/ Pneumatic interchangeable
● Actuator Pressure: 5bar-6bar
● Outlet Connection: Weld, Clamp, Special interface
● New diaphragm design
● Maintenance is simple, safe, easy to operate
● Self-emptying
● Minimize dead angle
● Excellent value KV
● CIP/ SIP sterilization and cleaning

Radial Diaphragm Valve
●Mainly used in pharmaceutical, biotech, health care, cosmetic and food industries, etc.
●In the pharmaceutical industry, valves can be used as process control valve, dosing valve, sampling valve and aseptic drain valve, etc.
●In the food industry, valves are often used as guide device, such as sampling valve, dosing valve (For example adding CO2/Nitrogen to beer, add seasoning to drink). Radial diaphragm valves are mainly manually and pneumatically operated with inside body finished Ra≤0.5 um, in order to meet the requirements of biopharmaceutical industry.
● Size: 3/4 "-2.5", DN20-DN65
● Working Temperature: -10 ℃ to 120 ℃ (EPDM/ Silcon)
● Maximum Pressure: 6bar
● Operation: Manual/ Pneumatic interchangeable
● Actuator Pressure: 5bar-6bar
● Outlet Connection: Weld, Clamp, Special interface
● New diaphragm design
● Maintenance is simple, safe, easy to operate
● Self-emptying
● Minimize dead angle
● Excellent value KV
● CIP/ SIP sterilization and cleaning

Multi port Diaphragm Valve M-65A is the most progressive design for meeting high clean in pharmacy industry. Assembly of traditional welding manifold valve systerm is complicated, implementation of period is long, large space is ooccupied with expensive cost on inspection.

5 control valves, 6 ports
5 valves vertical place
Dead zone = ≤ 1D
Size: 1"-2",DN25-DN50
Material: 316L/1.4404，1.4435 NB2 Fe＜0.5%
Temperature: -20℃ +150℃
Pressure: 10bar
Inner Surface Treatment: Ra0.4μm, Mechanical polishing, Electro polishing
Diaphragm: Double diaphragm: EPDM+PTFE; Single diaphragm: EPDM, FPM, Silicon
Operations: Manual/Pneumatic
Control: configurable, 1) Control Unit C-TOP, 2) positioner IL-TOP, 3) mechanical valve regulator, 4) Position Sensor