Valve

DJ-FDT butterfly valve is mainly designed for powder, granule, capsule and other container equipment systems. The butterfly valve has the characteristics that standard butterfly valve does not have, such as ultra-small torque, seal opening and closing does not produce excessive friction, long life, No seal powder shedding, ultra-short valve body, and adjustable pressure. The valve does not require professional tools to be disassembled, maintained, cleaned, safe, reliable, low cost, simple to operate, and can be interchanged manually, pneumatically, or electrically.
Specifications: 4''-10'', DN100-DN250
Connection method: clamp, welding, flange, bottom flange, DIN 3A INCH
Material: 316L/1.4404/1.4435
Seal: White SILCON (recommended) Gray FKM (selection)
Execution mode: manual, pneumatic, electric interchangeable
Surface treatment: Ra 0.6μm (recommended); Ra 0.4μm (selection)
External surface: matt (recommended) bright blasting electropolishing
Applicable: vacuum, high temperature 130 ° C, CIP cleaning, SIP sterilization, etc.

DJ-FDT butterfly valve is mainly designed for powder, granule, capsule and other container equipment systems. The butterfly valve has the characteristics that standard butterfly valve does not have, such as ultra-small torque, seal opening and closing does not produce excessive friction, long life, No seal powder shedding, ultra-short valve body, and adjustable pressure. The valve does not require professional tools to be disassembled, maintained,
cleaned, safe, reliable, low cost, simple to operate, and can be interchanged manually, pneumatically, or electrically.
Specifications: 4''-10'', DN100-DN250
Connection method: clamp, welding, flange, bottom flange, DIN 3A INCH
Material: 316L/1.4404/1.4435
Seal: White SILCON (recommended) Gray FKM (selection)
Execution mode: manual, pneumatic, electric interchangeable
Surface treatment: Ra 0.6μm (recommended); Ra 0.4μm (selection)
External surface: matt (recommended) bright blasting electropolishing
Applicable: vacuum, high temperature 130 ° C, CIP cleaning, SIP sterilization, etc.

The sampling valve has a dead angle-free design and the end face connected to the container does not have a dead zone phenomenon.
◎ It is mainly used for sample collection of materials in tank equipment or pipelines. It can also be installed at the lowest point of tank equipment or pipelines to drain residual liquid.
◎Working principle: the handwheel rotates the valve stem clockwise together with the sealing ring. At this time, the valve is opened for sampling. The handwheel rotates the valve stem counterclockwise together with the sealing ring. The valve is closed.
◎Applicable temperature: -10 ° C to 130 ° C
◎ valve body material: AISI 304 AISI 316L
◎ Sealing material: PTFE
◎Connection method: clamp type, thread type, welding type, nut type

equipment systems. The butterfly valve has the characteristics that standard butterfly valve does not have, such as ultra-small torque, seal opening and closing does not produce excessive friction, long life, No seal powder shedding, ultra-short valve body, and adjustable pressure. The valve does not require professional tools to be disassembled, maintained, cleaned, safe, reliable, low cost, simple to operate, and can be interchanged manually, pneumatically, or electrically.

Specifications: 4''-10'', DN100-DN250
Connection method: clamp, welding, flange, bottom flange, DIN 3A INCH
Material: 316L/1.4404/1.4435
Seal: White SILCON (recommended) Gray FKM (selection)
Execution mode: manual, pneumatic, electric interchangeable
Surface treatment: Ra 0.6μm (recommended); Ra 0.4μm (selection)
External surface: matt (recommended) bright blasting electropolishing
Applicable: vacuum, high temperature 130 ° C, CIP cleaning, SIP sterilization, etc.

DJ-FDT butterfly valve is mainly designed for powder, granule, capsule and other container equipment systems. The butterfly valve has the characteristics that standard butterfly valve does not have, such as ultra-small torque, seal open/close does not produce excessive friction, long life, No seal powder shedding, ultra-short valve body and adjustable pressure. The valve does not require professional tools to be disassembled, maintained, cleaned, safe, reliable, low cost, simple to operate and can be interchanged manually, pneumatically or electrically.
Specifications: 4''-10'', DN100-DN250
Connection method: clamp, weld, flange, bottom flange, DIN 3A INCH
Material: 316L/1.4404/1.4435
Seal: White SILICON (recommended) Gray FKM (selection)
Execution mode: manual, pneumatic, electric interchangeable
Surface treatment: Ra 0.6μm (recommended); Ra 0.4μm (selection)
External surface: matte (recommended) bright blasting electropolishing
Applicable: vacuum, high temperature 130 ° C, CIP cleaning, SIP sterilization, etc.

The level gauge is mainly applied to the tank equipment. The two same gauges or two different gauges are assembled on the tank so that the liquid condition or capacity can be observed and the sample can be extracted.
◎Size:1/4",3/8",1/2",3/4"
◎Connections: thread, clamp, weld
◎Certificate: PED 97/23/EC,FDA 177.2600
◎when turn the hand wheel clockwise, the valve shaft and seal rise up. At this time, valve is open for sampling. When turn the hand wheel anti-clockwise, the valve shaft and seal go down,at that time, the valve is closed.
◎Thread; Nut; welding; Clamps

◎its mainly applied to extract sample from tank or pipeline. It also can be assembled at the bottom of the tank or pipeline to drain away the waster liquid
◎Operating principle：when turn the hand wheel clockwise, the valve shaft and seal rise up. At this time, valve is open for sampling. When turn the,hand wheel anti-clockwise, the valve shaft and seal go down,at that time, the
valve is closed.
◎Applicable temperature：－10℃ -130℃
◎Body material：AISI 304 AISI 316L
◎Seal material：PTFE
◎Connection: clamp, threaded, welded, Nut、

◆The valve seat opens inside of tank or other equipment that it can avoid opening by accident due to much pressure in the pipes.
◆The valve is normally closed(by spring). The valve is open as soon as pushing the handle and closed when loosing up.
◆The design of completely drainage water is to avoid remains inside the valves. Technical specification
◆Material：316L
◆Temperature：130℃
◆Pressure：10bar

◆Straight sampling valve open inside of tank or other equipment that it can avoid opening by accident due to much pressure in the pipes.
◎Operating principle:when turn the hand wheel clockwise, the valve shaft and seal rise up. At this time, valve is open for sampling. When turn the,hand wheel anti-clockwise, the valve shaft and seal go down,at that time, the valve is closed.
◎Temperature：－10℃ -130℃
◎Body material： AISI 304 AISI 316L
◎Seal material： PTFE
◎Connection: clamp, thread, weld, Nut

Mini type diaphragm sampling valve manual / pneumatic operation, T type, L-type 3 way, U-type 3 way, straight type etc. These valves are mainly used in the solid-liquid sampling on biological systems, laboratories and other projects.
Design Features
●Size: 1/4 "-3/4"，DN6-DN15
●Diaphragm PTFE+EPDM/Silicong/EPDM/FPM
●Max temperature: 150℃, ok for CIP/SIP
●Max pressure: 10bar
●Standards: BPE 3A DIN ISO IDF
●Material：316L,1.4404
●Max temperature: - 30 to 150 ℃ (depending on seal material) (stainless steel actuator)
●Max temperature: - 30 to 130 ℃ (depending on seal material) (plastic actuator)
●Max pressure: one way (DELTA P = 100%)
Normally close EPDM 8 bar, PTFE 6 bar (option)
Normally close EPDM 6 bar, PTFE 4.5 bar (standard)
Normally open and double action EPDM 8 bar, PTFE 6 bar
●Certificate: PED/97/23/EC，3A/54-04/1580，FDA.177.2600

◆The aseptic sampling valve is designed for sterilization before and after each sampling.
◆Open to Sampling-Valve is opened by rotating the handle
◆Closed to Sterilizing-The built-in spring closes the valve. Do Keep hose channel open while sterilizing and recommend to install a small safety valve on the outside if sterilizing by steam.
◆Connection: clamp, welding, tank connector, multi-channel pipeline connector
◆Valve body material：AISI 316L（1.4404）ASME BPE 316L
◆Diaphragm：EPDM PTFE
◆Max. Temperature：130℃(EPDM)
◆Max. Temperature：150℃(PTFE)
◆Pressure： 10bar
◆Certificate：3-A-55-02，PED/97/23/EC

◆The aseptic sampling valve is designed for sterilization before and after each sampling.
◆Open to Sampling-Valve is opened by rotating the handle
◆Closed to Sterilizing-The built-in spring closes the valve. Do Keep hose channel open while sterilizing and recommend to install a small safety valve on the outside if sterilizing by steam
◆Application: The aseptic sampling valve is applied to beer, milk, beverage, fruit juice, pharmacy industries etc.
◆Connection: Welding, Clamp.
◆Valve body material：AISI 316L（1.4404）ASME BPE 316L
◆membrane：EPDM PTFE
◆Max. Temperature：130℃(EPDM)
◆Max. Temperature：150℃(PTFE)
◆Pressure：10bar
◆Certificate：3-A-55-02，PED/97/23/EC

◆The aseptic sampling valve is designed for sterilization before and after each sampling.
◆Open to Sampling-Valve is opened by rotating the handle
◆Closed to Sterilizing-The built-in spring closes the valve. Do Keep hose channel open while sterilizing and recommend to install a small safety valve on the outside if sterilizing by steam.
◆Appplication: The aseptic sampling valve is applied to beer, milk, beverage, fruit juice, pharmacy industries etc.
◆Connection: clamp, welding
◆Valve body material：AISI 316L（1.4404）ASME BPE 316L
◆Membrane：EPDM PTFE
◆Max. Temperature：130℃(EPDM)
◆Max. Temperature：150℃(PTFE)
◆Pressure：10bar
◆Certificate：3-A-55-02，PED/97/23/EC

◎Specifications:DN8-DN50,1/2"-2"
◎Material：CF8/304，CF8M/316
◎Nominal pressure：PN1.6，2.5，4.0，6.4MPa
◎Strength test pressure：PN2.4，3.8，6.0，9.6MPa
◎High pressure seal pressure test：1.8，2.8，4.4，7.1MPa
◎Applicable medium：H1 H-(16-64)C Water, oil, gas
◎Applicable temperature：-40~180℃

◎Check valve is designed to prevent fluid from flowing back and ensure the flow to one way direction.
◎It can be used to reduce the loss of fluid back suction,avoid pipe is shock by liquid
◎It is used in the food-processing, beverages, winery, oil, cosmetics,pharmaceuticals and chemicals industries.
◎The valve is open when pressure of the fluid exceeds the spring pressure and it is closed when the two pressures are close equal.And stronger counter-pressure also makes the valve closed.
◎Specifications: DN-25/1" TO DN-100/4"
◎Boby/shaft: AISI 316L/304
◎Spring: AISI 304
◎Seal: EPDM according to FDA177.2600
◎Surface Treatment: Ra ≤0.8 μm
◎Seal: NBR, FPM (Viton) or PTFE. FDA 177.2600(optional)
◎Connections: weld, thread, clamp, DIN, SMS, RJT, IDF, ISO,3A
◎Max. pressure：10 bar
◎Opening pressure：0.3bar(DN-25) 0.2bar(DN-32/40) 0.1bar(DN-50/100)
◎Working temperature ： -10℃ to 130℃(EPDM)

Pneumatic angle seat valve with control unit is a general switch in the automatic control system widely used in printing, dyeing, bleaching, food,washing,chemical, water treatment, pharmacy and other automatic machinery and equipment. It is featured with water hammer protection,noise-free, reliable sealing performance.

Size：1/2"-3",DN10-DN80
Material：CF8、CF8M
Connection : Clamp, weld, thread，BSP/BSTP/NPT,DIN,Inch
Control unit
Position feedback, Can be viewed on (Green) off (Red)
Built-in Solenoid valve
Valve opens– green light
Valve closes-red light
The design has inching button (manual design)
Power Supply：DC 24V ±10%
Air supply：M5/Φ4

Pneumatic angle seat valves with Positioner is mainly used in the flow control valve adjustment. The medium contacting with the valve and the position is only stainless steel and PTFE. Maximum temperature can reach to 180 ℃, pressure up to 20bar. It can also be used in vacuum environment. According to the design of valve body without dead angle, surface roughness up to Ra0.4 μ m,valve seal with embedded designs, it is used very broadly covering almost all sectors, such as pharmaceuticals, food andbeverage, brewery, chemical and other industries. The valve is particularly suitable for steam flow regulating control system.

◆Size: 1/2"-3", DN10-DN80
◆Material: CF8/304、CF8M/316
◆Connection : Clamp,thread,flange,BSP,BSP,NPT,DIN
◆Working pressure：8bar(standard) 10bar(Options)
◆Working temperature：120℃(standard) 180℃(Options)
●0/4...20mA to 0...5/10V（standard）
●0/4...20mA Position feedback output (Options)
●Device NET Device Net bus control (Options)
●Support single self-tuning function
●Protection grade IP67
●Power Supply DC 24V ±10%
●Support manual and automatic operation

Pneumatic angle seat valve is a general switch in the automatic control system which is widely used in printing, dyeing, bleaching, food,washing,chemical, water treatment, pharmacy and other automatic machinery and equipment. It is featured with water hammer protection,noise-free, reliable sealing performance.
Design Features
● Size: 1/2"-2 1/2", DN10-DN65
● Material: CF8/304、CF8M/316
● Connection : Clamp,thread,flange,BSP、BSP、NPT,、DIN
● Pneumatically operated:
1）Can be configured to position sensor
2）valve locator (process controller)
3）Valve position Regulator
4）MINI C-TOP Control unit
●Manual pneumatic interchangeable
●Working pressure：8bar(standard) 10bar(option)
●Working temperature：120℃(standard) 180℃(option)

Application
Angle seat valve is a general switch in the automatic control system which is widely used in printing, dyeing, bleaching, food,washing,chemical, water treatment, pharmacy and other automatic machinery and equipment. It is featured with water hammer protection,noise-free, reliable sealing performance.

Design Features
● Size: 1/2"-2 1/2", DN10-DN65
● Material: CF8/304、CF8M/316
● Connection : Clamp,thread,flange,BSP、BSP、NPT,、DIN
● Pneumatically operated:
1）Can be configured to position sensor
2）valve locator (process controller)
3）Valve position Regulator
4）MINI C-TOP Control unit
●Manual pneumatic interchangeable
●Working pressure：8bar(standard) 10bar(option)
●Working temperature：120℃(standard) 180℃(option)

◎ Specifications: DN8-DN50,1 / 2 & quot; -2 & quot;
◎ Nominal pressure: PN1 .6,2.5,4.0,6.4MPa
◎ strength test pressure: PT2.4,3.8,6.0,9.6MPa
◎ High pressure seal pressure test: 1.8,2.8,4.4,7.1MPa
◎ Applicable medium: J11W- (16-64) C water, oil, gas, J11W- (16-64) P nitric acid, J11W- (16-64) R acetic acid
◎ Applicable temperature: -40 ~ 180 ℃
◎ Material: CF8, CF8M

◎Specifications：DN15-DN200,1/2"-8"
◎Nominal pressure：PN1.6-6.4, Class 150/300,10k/20k
◎Strength test pressure：PT1.5PN
◎High pressure seal pressure test：1.1PN
◎Applicable medium：J41H-(16-64)C water, oil, gas J41W-(16-64)P nitric acid J41W-(16-64)R acetic acid
◎Applicable temperature：-40~180℃
◎Material：CF8、CF8M

Horizontal pneumatic three way non retention ball valve, the hygienic design of the valve is widely used in the field of food processing, beverages, fruit juices, wine, biopharmaceutical with vary flexible body combinations, for example, L-Port or T-Port which can be interchangeable on-site Inlet and outlet to be any combination of changes for guaranting zero dead angle and no retention.

Technical specifications
Size：1"-4",DN25-DN100
Material：1.4301/304,316L/1.4404
Gaskets：PTFE,TFM(FDA 177.1550)
Max. temperature：-20℃ - 150℃(Standard)-30℃ - 200℃(Option)
Pressure:10-30bar(Depending on seal material and temperature)
Operating modes:manual, pneumatic, electric
Surface finishing:Internal surface Ra0.6μm, external surface sand blast
Certificate：3-A-68-00，PED/97/23/EC
Configuration Controls：process controller/valve positioning ，0/4....20mA,0 5/10V(see controller directory)(Option)
Top of the valve control unit，AS-1 Device Net bus communication terminal connection(Option)
position sensor PNP NPN(Option)

Three way non-retention ball valve, the hygienic design of the valve is widely used in the field of food processing, beverages, fruit juices, wine, biopharmaceutical with vary flexible body combinations, for example, L-Port or T-Port which can be interchangeable on-site Inlet and outlet to be any combination of changes for guaranting zero dead angle and no retention.

Technical specifications
Size：1"-4",DN25-DN100
Material：1.4301/304,316L/1.4404
Gasket：PTFE,TFM(FDA 177.1550)
Max. temperature：-20℃ - 150℃(Standard)-30℃ - 200℃(Option)
Pressure:10-30bar(Depending on seal material and temperature)
Operating modes:manual, pneumatic, electric
Surface finishing:Internal surface Ra0.6μm, external surface sand blast
Certificate：3-A-68-00，PED/97/23/EC
Configuration Controls：process controller/valve positioning ，0/4....20mA,0 5/10V(see controller directory)(Option)
Top of the valve control unit，AS-1 Device Net bus communication terminal connection(Option)
position sensor PNP NPN(Option)

Pneumatic three way non-retention ball valve, the hygienic design of the valve is widely used in the field of food processing, beverages, fruit juices, wine, biopharmaceutical with vary flexible body combinations, for example, L-Port or T-Port which can be interchangeable on-site Inlet and outlet to be any combination of changes for guaranting zero dead angle and no retention.

Technical specifications
Size：1"-4",DN25-DN100
Material：1.4301/304,316L/1.4404
Gaskets：PTFE,TFM(FDA 177.1550)
Max. temperature：-20℃ - 150℃(Standard)-30℃ - 200℃(Option)
Pressure:10-30bar(Depending on seal material and temperature)
Operating modes:manual, pneumatic, electric
Surface finishing:Internal surface Ra0.6μm, external surface sand blast
Certificate：3-A-68-00，PED/97/23/EC